
The correct coil belongs to a coil series intended for your tank or pod. The coil variant then determines the resistance, wattage range and liquid flow that the construction is designed for. The same ohm rating does not mean that two coils fit the same device.
The coil's construction, power and liquid feed affect flavour, the amount of aerosol and the consumption of e-liquid and battery energy.
What does a coil do in a vape?
The coil heats the e-liquid delivered to the heating surface through a liquid-absorbing material, usually cotton. The heating surface may consist of a spiral-shaped metal wire or mesh.
When the device is activated, the liquid is heated and forms an aerosol, often called vapour. The heating surface, liquid feed, power and airflow affect the heating and therefore the aerosol's temperature, amount and flavour.
Coils have different fits and operating conditions. A coil that fits one tank therefore does not automatically fit another. Our range of coils for vapes and e-cigarettes includes replacement parts from different coil series.
Can you use any coil?
No. The coil must fit the tank's or pod's coil series, dimensions, connection and seals. The device must also support the coil variant's power range and intended operating mode.
Aspire BP Stik shows why the full coil name is needed: it supports BP Meshed 0.15 ohm with a range of 60–80 W, but not BP Pro Meshed 0.15 ohm with a range of 80–100 W. The resistance is the same, but compatibility is different.
| Tank or device | Compatible variant | Specified power range |
|---|---|---|
| Innokin Zenith Minimal | Z-Coil 0.8 ohm, MTL | 15–18 W |
| Innokin Zenith Minimal | Z-Coil 0.3 ohm, RDL | 30–40 W |
| Innokin Sensis-EZ | Sceptre Coil 0.65 ohm, MTL | 9–12 W |
| Aspire BP Stik | BP Meshed 0.17 ohm | 45–55 W |
The coil's fit and the battery device's power support must both match. The wrong variant can cause leakage, insufficient heating or abnormal heat. Never force a coil into place if it does not fit.
What does ohm mean on a coil?
Ohm, with the symbol Ω, indicates electrical resistance. At the same voltage across the coil, lower resistance produces higher current and power. In a regulated device, the electronics convert the battery's energy into the coil's output; coil current and battery current are therefore different quantities.
The battery's load is affected by the delivered power, the battery voltage under load and losses in the electronics. The ohm rating alone indicates neither battery current, fit nor the correct wattage setting.
Coils are available, for example, in the ranges 0.15–0.3, 0.4–0.7 and 0.8–1.2 ohm. The inhalation method also depends on the construction: Zenith Minimal Z-Coil 0.3 ohm is intended for RDL and Sensis-EZ Sceptre Coil 0.65 ohm for MTL.
Lower resistance occurs in many constructions with higher power and more open airflow, but this relationship is not enough to choose a coil. More about the electrical relationship can be found in What does Ohm's law mean and why is it important for vaping?.
Which coil is suitable for MTL?
In Innokin Zenith Minimal, the Z-Coil 0.8 ohm is an MTL example with 15–18 W. In Sensis-EZ, the Sceptre Coil 0.65 ohm is another MTL example, with 9–12 W. MTL therefore does not require at least 0.8 ohm.
MTL means Mouth To Lung: the aerosol is first drawn into the mouth and then into the lungs, an inhalation sequence that also occurs when smoking cigarettes. The construction usually has a more restricted airflow than open DTL.
Coils of 0.8 ohm or higher occur in MTL constructions with lower power. Lower actual power during an activation of equal length requires less battery energy. Throat feel is affected by the liquid's composition, nicotine form, concentration and heating.
Thinner liquids with a higher PG proportion and blends with 50 percent VG and 50 percent PG occur in MTL devices. They are not a requirement for all MTL tanks; Go-Z also supports 70 percent VG and 30 percent PG. The inhalation methods are explained further in What is the difference between MTL and DTL?.
Which coil is suitable for DTL?
DTL requires a compatible coil and a tank or pod with airflow and liquid feed intended for direct-to-lung inhalation. Aspire BP Stik has adjustable airflow from restricted to more open direct-to-lung inhalation and supports, among others, BP Meshed 0.17 ohm at 45–55 W.
DTL means Direct To Lung. Coils below 0.5 ohm occur in such constructions, together with airflow paths and liquid feed intended for direct-to-lung inhalation.
More open airflow and higher power can result in more aerosol and greater liquid consumption. Higher power during an activation of equal length requires more battery energy. At the same time, aerosol temperature is affected by, among other things, airflow and construction; DTL does not automatically mean warmer aerosol. Some DTL tanks are intended for a high VG proportion, such as GoMax, which is specified for 70 percent VG or more.
What is RDL and which coil is suitable for it?
RDL means Restricted Direct Lung: direct-to-lung inhalation with a more restricted airflow than open DTL. Zenith Minimal Z-Coil 0.3 ohm is intended for RDL at 30–40 W.
Coils in the 0.4–0.8 ohm range also occur in RDL constructions. Aerosol volume, flavour and battery consumption are affected by power, liquid feed and activation time.
How does the coil affect flavour?
The coil's heating and liquid feed affect which flavour changes are noticeable. Resistance, material, mesh or wire, wattage setting, airflow and the e-liquid's composition work together.
Build-up and changes in the liquid-absorbing material can affect performance as the coil is used. However, weaker or uneven flavour alone does not show that the coil is worn out. A dry or burnt flavour can occur when the liquid feed is insufficient; stop activating it then. Burnt cotton cannot be restored by refilling.
Other possible causes are covered in Why does my vape taste weaker than before?.
What is a mesh coil?
A mesh coil has a mesh-like or perforated metal surface instead of a traditional spiral-shaped heating wire. Depending on the construction, it may have a larger contact area with the liquid-absorbing material.
Contact area, applied power and liquid feed affect how the heat is distributed. Mesh is found in both smaller pod systems and larger tanks, and heat distribution depends on the entire construction. The construction is explained further in What are mesh coils?.
Which coil is suitable for which e-liquid?
The liquid needs to suit the tank's and coil's liquid feed. Innokin specifies 50 percent VG and 50 percent PG, or 70 percent VG and 30 percent PG, for Go-Z. For GoMax, 70 percent VG or more is specified.
PG is propylene glycol and VG is vegetable glycerin. VG is more viscous. A higher VG proportion therefore requires a feed system capable of handling the thicker liquid, such as larger liquid openings.
If the liquid is too viscous for the feed system, the liquid-absorbing material may dry out during heating. This can produce a dry or burnt flavour. A thinner liquid may leak more easily in some constructions, but leakage can also be caused by seals or assembly. Higher power does not solve insufficient liquid feed.
More about the blends can be found in VG/PG ratios.
How do you know which wattage range to use?
The wattage range belongs to the exact coil variant and is stated on the coil, packaging or in the manufacturer's specifications. Aspire BP Coil 0.6 ohm for BP Stik, for example, is specified for 15–25 W.
A marking of 40–60 W indicates that variant's power range. The wattage range cannot be calculated from the ohm rating.
Too little power can result in insufficient heating, less aerosol or altered flavour. Power above the intended range can overheat the heating surface and damage the liquid-absorbing material. Even within the range, insufficient liquid feed can cause a burnt flavour.
For Innokin Ajax 0.35 ohm, the manufacturer specifies 30–55 W and starting at 30 W after preparing the coil. This is an example of starting at the lower end of the range; further adjustment should be made within the specified range. Devices with automatic power do not offer the same opportunity to select wattage freely. Power settings are also discussed in What wattage should I vape at?.
How do you know when it is time to replace the coil?
Stop using it if there is a burnt flavour. If the liquid-absorbing material has burnt, the coil needs to be replaced. In a construction with a fixed coil, the entire intended pod or tank is replaced, such as the GoMax tank.
| Sign | What it may indicate |
|---|---|
| Weaker flavour | May be caused by build-up or wear, but also by liquid feed, liquid or settings. |
| Dry or burnt flavour | Stop activating it. Dry material may be due to insufficient feed; burnt material needs to be replaced. |
| Less aerosol | May be caused by power, battery level, contact or liquid feed. |
| Gurgling | May be caused by excess liquid or condensation. |
| Different liquid flavour | May be caused by the coil or the liquid. Flavour alone determines neither whether replacement is needed nor whether the liquid is safe. |
| Longer use than previously | Liquid, power, frequency of use and saturation affect how quickly the coil wears out. |
Before checking or replacing: disconnect the charging cable, switch off the device and let the parts cool down. The fill level, assembly and accessible contact surfaces can then be checked without activation. Wipe condensation from the intended accessible surfaces; do not rinse the coil itself in an attempt to restore burnt cotton. In the event of abnormal heat, damage, swelling or suspected liquid in the electronics, stop both use and charging.
Preparation and liquid feed are covered in 5 tips for avoiding burnt coils.
How do you choose the right coil step by step?
The choice begins with compatibility between the device, tank or pod and coil series. Next, select a supported variant with the correct power range and liquid requirements.
- Start with the exact tank or pod. Zenith Minimal uses Z-coils, for example; a similar appearance on another coil is not enough.
- Match the full variant name with the device's support. BP Stik supports BP Meshed 0.15 ohm, but not BP Pro Meshed 0.15 ohm.
- Match the inhalation method and construction. Zenith Minimal has, for example, Z-Coil 0.8 ohm for MTL and Z-Coil 0.3 ohm for RDL.
- Match the power range with the device. The two Zenith variants above are specified for 15–18 W and 30–40 W respectively; the tank's fit does not guarantee the battery device's power support.
- Match the liquid with the feed system. Go-Z is specified for 50VG/50PG or 70VG/30PG; GoMax is specified for 70 percent VG or more.
- Install the intended replacement part with the device switched off and disconnected from charging. For Go-Z, moisten the accessible cotton before filling. Fill and close the tank or pod and allow the wick to become fully saturated before activation; Go-Z requires at least five minutes after filling and the Sensis-EZ manual specifies five minutes for a new coil. Liquid must not be poured into the airflow channel. A screw-in coil, a push-fit coil and a pod with a fixed coil are replaced in different ways.
Quick Facts
- Reading Time
- 10 min
- Popularity
- Very Popular
- Category
- Coils, pods & tanks
- Published
- 2026-06-09
Related Products
Products mentioned in this article





