Troubleshooting & maintenance

Why E-Liquid Sometimes Gets into the Airflow Channel

  • 2026-06-03
  • Author: dennis danielsson
  • Updated: 2026-10-17
  • 4 min read
  • Very Popular(1086)
Why E-Liquid Sometimes Gets into the Airflow Channel

E-liquid can end up in the airflow channel through overfeeding or leakage from the reservoir. Condensation and aerosol droplets can also collect on the channel surfaces. Stop activation if liquid droplets or hot liquid come up through the mouthpiece.

What is the airflow channel?

The channel directs air past the heating surface and aerosol onward toward the mouthpiece. Gaseous components can condense when cooled, and small aerosol droplets can adhere to the surfaces. Liquid can therefore collect even without an unsealed reservoir. Larger accumulations can obstruct airflow.

Why does liquid end up there?

Filling, overfeeding, unsealed parts and liquid from the aerosol flow can bring liquid into the channel.

Filling

Overfilling or filling into the air channel can bring liquid into the airway. Fill through the designated opening and close it afterward. Aspire Flexus Pro has a silicone seal on the side of the pod. Sealed prefilled pods should not be opened for refilling.

Coil, wick and seals

The wick should be thoroughly saturated. Excess liquid in the airway, however, is a different condition. Residue, a burnt wick, damaged seals and a cracked pod can affect liquid feeding and the path of the liquid.

Liquid viscosity

E-liquid with more PG is usually more fluid, while more VG gives higher viscosity. Temperature and other ingredients also have an effect. Liquid that is too thin can overfeed a design; liquid that is too viscous may feed too slowly.

Innokin specifies 50VG/50PG and 70VG/30PG for MTL use of the Go-Z. Some recipes can damage the tank’s polycarbonate, so the base ratio alone is not enough to determine material compatibility.

Heat and pressure

Heat can change the liquid’s viscosity and the pressure conditions in the reservoir. Avoid hot cars, direct sunlight and placement near radiators. A change in liquid movement does not automatically mean that the seal is worn out.

Storage position

Position affects which openings the liquid reaches, together with filling and construction. Vaporesso recommends upright storage for the XROS series. A crack or damaged seal still needs to be replaced.

Draws and activations

Strong negative pressure can increase liquid flow in some designs. Frequent activations add heat and consume liquid, which instead can result in feeding that is too slow. Do not clear the channel with harder, longer or repeated draws.

How can it be noticed?

  • Gurgling when air passes through liquid.
  • Droplets or hot liquid from the mouthpiece.
  • Uneven aerosol, which can also be caused by feeding, power, connection or battery function.
  • Liquid at the air intake.
  • Weak or changed flavour caused, for example, by liquid, feeding or residue.
  • Liquid around the pod or tank from leakage, condensation or deposited droplets.

The symptoms can have several causes. Do not investigate recurring accumulation or malfunction with continued test activations.

What should I do if liquid comes out?

Stop using the device if droplets or hot liquid come from the mouthpiece. Rinse your mouth if liquid has entered it. Wash skin with water and soap; rinse immediately with water in case of eye contact.

Nicotine-containing liquid can cause poisoning. In case of suspected poisoning, contact the Poisons Information Centre at 010-456 6700 in less urgent cases, or call 112 and ask for the Poisons Information Centre when urgent. Do not wait for symptoms.

Also stop charging in the event of abnormal heat, damage, swelling, self-activation or suspected liquid in the electronics. Do not test-charge it to see whether the fault goes away.

How are filling and cleaning handled?

  • Filling: use the correct opening, do not overfill and close the seal.
  • Liquid: the recipe and viscosity need to suit the feeding system and materials.
  • Storage: protect from sunlight and intense heat and follow the position intended by the design.
  • Wiping: disconnect the cable, switch off and allow to cool. Wipe the accessible mouthpiece, air intake and contacts with a dry, soft cloth. Dry connection cleaning is specified for Innokin Sceptre.
  • Contacts: do not bend or scrape the pins. Do not open or rinse the electronics.
  • Persistent fault: refrain from continued use in the event of major leakage, abnormal heat or uneven operation. Do not blow through the device and do not use a heat pulse or higher wattage as cleaning.

When should the pod or coil be replaced?

Burnt cotton and damaged parts need to be replaced. Refilling and cleaning do not restore burnt cotton. Gurgling or weak aerosol can, however, be caused by other faults.

Aspire Flexus Pro is available with a replaceable AF coil and with a fixed coil. In the first case, the coil is replaced; in the second, the pod. A cracked pod or damaged seal is handled as separate damage. Sealed prefilled pods are not opened for coil or wick replacement.

For e-liquid containing nicotine:

Contains nicotine, which is a highly addictive substance. Age limit: 18 years.

Nicotine warning

Quick Facts

Reading Time
4 min
Popularity
Very Popular
Category
Troubleshooting & maintenance
Published
2026-06-03

Related Products

Products mentioned in this article